Sākumlapa » Datori & IT»Robotika»Izstrādes plates»Adafruit Perma-Proto HAT for Pi Mini Kit - No EEPROM

Adafruit Perma-Proto HAT for Pi Mini Kit - No EEPROM

Pamatinformācija

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi A+, B+, or Pi 2 with this jaunty prototyping HAT kit. To kick off the Adafruit HAT party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prot

Prece ir arhivēta

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi A+, B+, or Pi 2 with this jaunty prototyping HAT kit.

To kick off the Adafruit HAT party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more. The holes are connected underneath with traces to mimic the solderless breadboards you're familiar. There's also long power strips for +3V, +5V and Ground connections to the Pi. Near the top we break out nearly every pin you could want to connect to the Pi (#26 didnt quite make the cut).

This is just the basic version of our Perma-Proto HAT.It comes with a printed circuit board and a single 2x20 GPIO Header for to put your Perma-Proto on top of your Raspberry Pi (like a nice little hat...) This version does not come with an EEPROM so you can 'stack' it with other HATs without worrying about an EEPROM address collision.

You can customize your Perma-Proto setup using a standard 2x20 stacking header or extra tall 2x20 stacking header. You can also swap out the 2x20 header with a slim 2x20 type if you want it to sit closer to the Pi, or an extra tall one if you want it to sit above the USB/Ethernet ports.

A bit of light soldering is required to attach the header to the PCB but it's easy work.

This hat is only compatible with the Raspberry Pi A+, B+ or Pi 2! It will not work with the Raspberry Pi Model A or B.

Our initial version has the +3V and +5V markings in blue, and the GND markings in red, future orders will have these colors swapped to better match a solderless breadboard

  • Header Dimensions: 5mm x 51mm x 12mm
  • PCB Dimensions: 66mm x 57mm x 2mm

Produktu kodi

Ražotāja kods
ADA2310

Pasūtījumiem virs 99 € Photopoint piedāvā bezmaksas piegādi Igaunijas teritorijā. Ieskatieties cilnē „Piegāde”, lai iegūtu precīzāku piegādes cenu aprēķinu.

Jūs varat izvēlēties vēlamo piegādes veidu iepirkumu grozā:
Omniva paku termināls

Jūs varat pasūtīt preces uz jebkuru no Omniva paku termināļiem. Izvēlieties vēlamo termināli iepirkumu grozā. Līdzko sūtījums ieradīsies, Jums tiks nosūtīts SMS ziņojums ar unikālu kodu. Dodieties uz termināli nedēļas laikā, ievadiet kodu un paņemiet savu sūtījumu. Tas ir tieši tik vienkārši!
Omniva paku termināļu adreses skatīt šeit. Omniva kurjera piegāde

Kurjers nogādās Jūsu preces no Photopoint tieši uz Jūsu norādīto adresi. Piegāde tiek veikta darba dienās no 08:00 līdz 17:00. Kurjers Jums piezvanīs pirms ierašanās, tāpēc turiet savu telefonu tuvumā. Lūdzu, pārliecinieties, ka piegādes galamērķī atrodas persona, kas būs ir tiesīga saņemt sūtījumu.
Prece nav pieejama. Papildus informācijai par pieejamību un iepriekšēju pasūtīšanu, lūdzu, sazinieties ar mums šeit.

Preču salīdzinājums

Aizvērt